Skip to content
Cladding spraying guide

Cladding spraying explained: how a respray works, start to finish

Cladding spraying is the on site recoating of existing metal cladding with a specialist coating system.

Published 25 October 2026 · 7 minute read

The short answer

Cladding spraying is the on site recoating of existing metal cladding with a specialist coating system. The panels are cleaned, corrosion is treated, the surroundings are masked and a new primer and topcoat are sprayed on. It restores the colour and the protection without new sheets, usually while the building stays open.

What cladding spraying is

Most industrial and commercial units in the UK are clad in profiled steel or aluminium sheets that left the factory with a coil coating, usually plastisol or PVF2. Over the years sunlight breaks that coating down. The colour fades and the surface turns chalky, and in time the cut edges and overlaps start to rust. The steel underneath is often still perfectly sound.

Spraying puts a new coating system over that tired finish, in place on the building. Nothing is taken down. Done properly, the result looks like new cladding and is backed by a written manufacturer warranty. It is a different job from painting a wall with a roller: the coatings are made for metal, the preparation is thorough and the spray equipment lays an even, factory style film across the profile of every sheet. Our cladding spraying service page shows the work itself.

Which cladding can be sprayed

The survey identifies what your cladding is and which system suits it. Getting that match right is what makes a sprayed finish last.

  • Plastisol coated steel, the most common finish on industrial units, once it is cleaned and primed with a compatible system
  • PVF2 coated steel and aluminium, which needs a specific primer because the surface is designed to resist things sticking to it
  • Composite insulated panels, as long as the facings are sound and not delaminating
  • Roller shutters, personnel doors, frames and flashings, usually done at the same time so the whole building matches
  • UPVC fascias, windows and cladding boards, using coatings made for plastic

The job, stage by stage

Survey. We visit the building, measure the elevations, note the existing coating and check its condition: chalking, fading, cut edge corrosion, damaged or holed sheets, failed sealant and loose fixings. We also agree access, working hours and which areas of the site need clearing. You get a written price and timescale from this visit.

Cleaning. Every surface is washed to remove dirt, chalk, algae and traffic film. A coating sticks only as well as the surface beneath it, so this step matters more than any other. We use low pressure and suitable cleaning solutions so the existing finish is not damaged. Our cladding cleaning guide covers it in detail.

Corrosion and repairs. Rust at the cut edges and sheet laps is taken back to a sound surface and treated before any colour goes on. Damaged sheets are repaired or replaced, fixings are tightened or changed, and failed sealant is renewed. Spraying over active rust only hides it for a while. More on that in what is cut edge corrosion.

Masking. Windows, doors, signage, lights, the ground, vehicles and neighbouring property are covered. Overspray is the worry most building owners raise first, and careful masking plus working to the wind is how it is controlled.

Primer. A primer matched to the existing coating goes on first. It is the link between the old surface and the new topcoat, and the wrong primer is the most common reason cheap resprays peel.

Topcoat. The finish colour is sprayed in an even, high build coat across the full profile of each sheet. We match to any RAL or BS reference, so a brand colour or the building’s original shade both come out as specified.

Handover. We walk every elevation with you, touch up anything that needs it, remove the masking, clear the site and confirm the warranty in writing.

Most commercial jobs take three to seven days on site, depending on the size of the building, its condition and the weather. Our guide on how long a respray takes goes through a typical week.

The weather

Coatings have rules about when they can go on. The surface must be dry, the air and steel must be above the manufacturer’s minimum temperature, and the steel must sit far enough above the dew point that condensation will not form under the paint. Spraying stops for rain and for strong wind. In practice the main season runs from spring to autumn, and winter work is planned around dry, milder spells. We build weather allowance into the timescale rather than rushing a coat on in poor conditions.

How long a sprayed finish lasts

A correctly specified and applied system lasts for many years, and the coating manufacturer backs it with a written warranty, typically ten years on cladding coating systems. Our warranty guide explains who stands behind it. The warranty for your building is confirmed with your quote.

How long it actually lasts depends on the preparation, the system, the exposure of the building and how it is looked after. A yearly wash helps any finish last longer.

When cladding spraying is the wrong answer

Spraying cannot fix structural problems, and a good contractor will tell you so. It is the wrong choice when:

  • Sheets are holed or rusted right through
  • Composite panels are delaminating, with the facing coming away from the insulation core
  • The building is leaking because of failed sheets or roof details rather than surface wear
  • The cladding is due to come off anyway, for example in a planned extension

Often the answer is a mix: replace the few sheets that have failed and spray the whole elevation so old and new match. We also install cladding, so you get a straight answer either way.

What cladding spraying costs

Every building is priced from a survey, because area, access, condition and the amount of masking all change the price. What moves the price is covered in our respray or replace cost guide.

Quick questions

Most profiled steel and aluminium cladding can, including plastisol and PVF2 finishes, as long as the right primer is used. Sheets that are holed or panels that are delaminating need repair or replacement first.

Want a straight answer about your building?

Send us a few details and a photo. We will come out, look at it properly and give you a written price.

Get a Free Quoteor WhatsApp us a photo