Published 31 October 2026 · 4 minute read
The short answer
Roller shutters can be resprayed in place, without taking them off or leaving the unit open to the weather. Flaking paint and surface rust are stripped back, the surround is masked, and a coating made for metal that flexes is sprayed across every slat. The shutter is then run up and down to check the finish.
Why shutters wear out faster than the building
A roller shutter takes more punishment than any other part of a commercial unit. It faces the weather all day, it gets clipped by forklifts and pallet trucks, and every time it opens each slat rolls round the barrel and flexes. The bottom rail sits in rainwater and road grime. So the shutter is usually faded, scratched and rusting at the edges long before the mechanism inside it has worn out.
Replacing a shutter is expensive, and it means a day with the unit open to the weather while the old one comes out and the new one goes in. When the curtain and the guides are still sound, spraying gives you a clean, hard wearing finish and leaves the shutter doing its job.
Why brushed paint on a shutter fails
Most shutters that look worse after a repaint were brushed or rollered by hand. Brushed paint sits thick in the joints between slats, and when the curtain rolls up those thick spots crack. Paint put over loose flakes or surface rust has nothing sound to hold on to, so it lifts within a season and takes the new colour with it.
A sprayed coating goes on as an even film across the face of every slat. We use coatings made for metal that flexes, and we never spray over loose paint or rust. Those two things are what decide whether the finish survives daily use.
How a shutter is resprayed
The shutter stays on the building throughout. The order of work is the same on a single reception shutter or a row of loading doors.
- Survey: we check each shutter and door, note any corrosion or damage and agree the colour with you
- Prep: old flaking paint and surface rust are stripped back and treated so the coating has a sound surface to bond to
- Mask: the surrounding cladding, brickwork, signage and ground are covered so the colour goes only where it should
- Spray: primer and topcoat are applied with controlled spray equipment, with the shutter set in a position that lets us reach every slat
- Check: the shutter is run up and down to make sure nothing binds and the finish is even, then the masking comes off
Doing the shutters and the cladding together
On many units the shutters, the personnel doors and the cladding are all tired at the same time. Doing them in one visit is usually the best value, because it means one set of access equipment, one round of masking and an elevation that comes back finished as a whole. Shutters can match the cladding or stand out from it. One unit we sprayed in North Lincolnshire came back in jupiter green with its doors and trims picked out in red.
The same visit can cover shutter boxes, sectional and up and over doors, personnel doors and frames, window frames, flashings, bollards and railings. Our roller shutter spraying page lists the lot, and cladding spraying explained covers the elevation itself.
When spraying is the wrong fix
A coating changes the surface of a shutter and protects it. It will not straighten a slat bent by a forklift, free a curtain that jams in its guides or cure a motor that is struggling. If a shutter sticks, drops or grinds, get the mechanism looked at before it is sprayed, so the new finish is not scraped off by a fault that was already there.
Slats that are holed or rusted right through need replacing first. The survey tells you which shutters can be sprayed as they are and which need work beforehand.
Keeping the loading doors working
A loading door that has to stay in use all day can still be sprayed. We plan the order of the doors around your deliveries, work on one opening while the others stay in use, and come back outside your hours for the door you cannot spare. Our guide to staying open during a respray explains how the work is planned around a busy yard.
What it costs
Shutters are priced per door after a free survey, and the price depends on the size of the shutter, its condition and how much prep the slats need before any coating goes on. Doing several doors, or doing them with the cladding, spreads the cost of access and masking. Our respray or replace guide covers what else moves a price.





