Published 31 October 2026 · 6 minute read
The short answer
Commercial cladding and roofs should be checked once a year and after any storm. Walk each elevation looking for chalking, fading, rust at the sheet laps, failed sealant and loose fixings, check that the gutters drain, and leave the roof itself to someone with safe access. Small faults found early are cheap to fix.
Why a yearly check is worth an hour
Cladding and roofs rarely fail all at once. They fail at the edges, at the laps, at the gutters and around the fixings, a little more each winter. Rust at a sheet lap is a brown line one year and a lifted band of coating a few years later. A gutter that overflows once in a storm stains the wall below it, then starts letting water in. Caught early, each of these is a small repair. Left, they become the reason a building needs new sheets.
There is a paperwork reason as well. Many coating guarantees expect the building owner to inspect the cladding regularly and keep it clean, so a yearly record of what you checked and what you found is worth keeping with the guarantee. Our commercial cladding cleaning guide quotes one manufacturer’s terms as an example. Check the document that came with your own building.
Before you start
Pick a dry, bright day, ideally soon after rain so you can see where water has been running. Take a photo of each elevation from the same spot every year, because a side by side comparison shows fading and staining that is easy to miss when you walk past the building every day.
Stay off the roof. Many rooflights are fragile and cannot take a person’s weight, and roof edges and gutters are work at height. Everything in this checklist can be done from the ground, from the yard and from inside the building. If you cannot see part of the roof safely, that part is a job for a survey.
Walls: what to check on each elevation
Walk the full length of every wall, including the sides nobody uses. The elevations that face the sun and the prevailing weather usually show wear first.
- Chalking: rub a clean, dry hand on a sunny elevation. Coloured powder on your palm means the top layer of the coating has broken down
- Fading: compare the colour on an exposed wall with a sheltered spot, such as behind a downpipe. A big difference means the pigment has gone
- Rust at the laps and bottom edges: brown staining or bubbling paint where sheets overlap, or along the bottom of the wall sheets, is usually cut edge corrosion
- Sealant: cracked or missing sealant around windows, doors and flashings lets water in behind the sheets
- Fixings: rusty, loose or missing screws, and the rust streaks that run down from them
- Damage: dents, holes and creases from vehicles, usually at bumper height near loading bays and parking. Our guide to damaged cladding panels covers the fixes
- Algae and dirt: green growth on shaded walls and grime that has built up since the last clean
Gutters and downpipes
Gutters are easiest to judge from the ground just after heavy rain. Look for water spilling over the gutter edge, dark streaks running down the cladding below, plants growing out of the gutter line, and downpipes that leak at their joints or discharge onto the wall. Inside the building, a damp patch or a drip line under the eaves often points to a gutter problem rather than a roof one. Blocked and failed gutters are behind a lot of the leaks we are called to, which is why gutter clearing and repair sit within our roof maintenance work.
The roof, from below
You can learn a lot about a roof without going near it. From inside the building on a bright day, look up for pinpricks of daylight, rust on the underside of the sheets at the laps, and stains or drips on the floor, racking or stock. From the yard or a neighbouring vantage point, look for sheets that have lifted at the edges, flashings that have come loose and rooflights that have gone green or cloudy.
Note where any leak appears and after what kind of weather. A leak that only shows in driving rain from one direction tells a surveyor far more than “the roof leaks”.
Shutters and doors
Check each roller shutter and personnel door for faded or flaking paint, rust along the bottom rail and the edges of the slats, and damage from vehicles. Run each shutter and listen for grinding or sticking, which is a mechanical fault to sort before any recoating. Our guide on whether roller shutters can be resprayed explains what can be done about a tired shutter.
What you see, and what it usually means
Use this as a quick key when you write up your notes.
| What you see | Where | What it usually means |
|---|---|---|
| Coloured powder on your hand | Sunny elevations | The coating is chalking. A clean will help, and a respray brings the colour and protection back |
| Brown line or bubbling paint | Sheet laps, bottom edges, eaves | Cut edge corrosion starting. Cheapest to treat now |
| Dark streaks below the gutter | Walls under the eaves | The gutter or an outlet is overflowing |
| Daylight or rust seen from inside | Underside of roof sheets | Laps, fixings or sheets need a closer look from safe access |
| Green growth | Shaded walls and rooflights | Due a clean, and rooflights letting in less light |
| Rust streaks from screws | Around fixings | Fixings corroding or loose, letting water in |
Keeping a record
Write down the date, what you checked, what you found and what was done about it, and keep the photos with it. Over a few years that record shows which parts of the building are wearing fastest, helps you plan and budget for work before it becomes urgent, and gives you something to show if you ever need to claim on a coating guarantee.
When to call in a survey
Call someone in if you find rust that is spreading, a leak you cannot trace, chalking across whole elevations, or any part of the roof you could not see safely. A clean is often the first step, because it shows the real condition of the cladding underneath, and our cladding cleaning visits finish with a note of anything we spotted.
We also carry out annual inspections of cladding, roofs and gutters. We survey the roof, gutters and laps, photograph the problem areas and give you a written report of what is urgent and what can wait, with a maintenance schedule if you want one. You can ask for a survey here.





