Published 31 October 2026 · 5 minute read
The short answer
Most leaking gutters on industrial units come down to blocked outlets, failed joints or steel gutters rusting from the inside. A blockage needs clearing. A few failed joints can be repaired and sealed, a gutter that is sound in shape but leaking along its length can often be lined, and one that has rusted through needs replacing.
Why gutters cause so many leaks on commercial buildings
Blocked and failed gutters are behind a lot of the leaks we are called to on factories and warehouses. Part of the reason is where the gutters sit. On many industrial buildings the gutter runs inside the line of the wall, or in the valley between two roof slopes, so when it overflows the water goes into the building instead of over the edge onto the yard. A gutter that would only cause a splash on a house can soak stock, racking and electrics on a unit.
Overflowing gutters also mark the outside of the building. The dark streaks that run down so many elevations below the eaves are usually water spilling over a blocked or sagging gutter, and they are one of the first things a clean shows up.
Where the water is coming from
Finding the cause comes before choosing the fix. These are the usual culprits.
- Blocked outlets and downpipes: leaves, silt and moss build up until water backs up and spills over
- Failed joints: the seal between two lengths of gutter dries out, cracks and lets water through at every joint
- Rust in the gutter sole: steel gutters corrode from the inside where water and silt sit, until the metal thins and holes
- Roof sheet laps near the gutter: cut edge corrosion at the bottom of the roof sheets lets water in just above the gutter, which can look like a gutter leak
- Damaged or sagging sections: a gutter knocked out of line by ladders, storms or the weight of standing water no longer drains to its outlet
Note where the drips appear inside, and after what weather. A drip that only shows in heavy rain points to an overflow. A drip that shows after any rain points to a joint or a hole.
Clear it first, then judge it
Clearing the gutters and outlets is the cheapest fix there is, and on plenty of buildings it is the whole answer. It also shows you the gutter properly. Once the silt is out you can see whether the joints are sound, whether the sole has rusted and whether the water now runs to the outlet. Gutter clearing is part of our external cleaning and our roof maintenance visits, so it can be done at the same time as the cladding.
Repair, line or replace
Once the gutter is clean, the condition of the metal decides the fix.
- Repair: a handful of failed joints or a small damaged section can be cut back, treated and resealed
- Line: where the gutter is still sound in shape but leaks at many joints or has surface rust along its length, a lining system is applied inside the existing gutter so the water runs over the lining instead of the old joints
- Replace: a gutter that has rusted through, split or lost its shape needs replacing, and we supply and fit new gutters and downpipes
Lining keeps the existing gutter in place, so there is no strip out and less disruption than replacement. The survey tells you which option suits each run, and a long gutter can need a mix of all three.
Working on gutters with the building open
Gutter work happens at height, often next to rooflights, many of which are fragile and cannot take a person’s weight. It is planned with safe access and the fragile areas protected, by a crew trained to IPAF, CSCS and SMSTS. CladCoat is CHAS and SafeContractor accredited. The work goes on above you while the building stays open, and we agree with you in advance which areas underneath need clearing and when.
Fix the gutters before a roof coating
If the roof itself is due for treatment, the gutters should be sorted first or at the same time. Corrosion treatment at the bottom edge of the roof sheets and a working gutter below it go together, and coating a roof while a failed gutter carries on leaking under it wastes the money spent on the roof. Our guide to the yearly cladding and roof check shows what to look for between visits.
What it costs
Gutter work is priced after a free survey, usually by the metre, and the price depends on the length of gutter, its condition, the access needed and whether it can be repaired, lined or needs replacing. You get a written price that sets out what is being done to each run.





